Apple Processor Cage and Clips Guía de instalación Pagina 65
- Pagina / 117
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Deploying the VSP OVF File
NOTE: The virtual service processor supports VMware ESXi versions 4.1 and later. For more
specific VMware environment support, see the VMware compatibility matrix on the VMware
website. The following set of instructions may vary depending on the version of VMware ESXi you
are using.
1. Insert the HP 3PAR Virtual Service Processor software DVD.
2. In the VMware vSphere Client window, select File > Deploy OVF template.
3. On the Source page, click Browse to locate the OVF file on the DVD.
4. Select the OVF file, click Open and then click Next.
5. On the OVF Template Details page, verify the OVF template is selected, and then click Next.
6. On the Name and Location page, create a name for the VSP, and then click Next.
7. On the Storage page, select a storage destination for the virtual machine files, and then click
Next.
NOTE: When deploying from the VMware VirtualCenter, specify the host to deploy the VSP
from the Host/Cluster page.
8. On the Disk Format page, select Thin Provision, and then click Next.
9. On the Network Mapping page, map the virtual machine to the networks in your inventory,
and then click Next.
10. On the Ready to Complete page, do the following steps:
a. Review the deployment settings.
b. Select the Power on after Deployment checkbox. Selecting this option powers on the VSP
after the installation is complete.
c. Click Finish.
A Deployment Completed Successfully message should appear after a few minutes.
11. Click Close.
12. On the left navigation pane, verify the system is on and the green icon is displaying on the
new VSP. If necessary, expanding navigation tree to find the deployed VSP.
a. Right-click the VSP in the virtual machine list.
b. Select Open Console.
The VSP is now ready to set up. Continue on to “Establishing the Virtual Service Processor IP
Address” (page 65).
Establishing the Virtual Service Processor IP Address
After verifying the connection to the Virtual Service Processor, you must perform one of the following
options:
• Option A: Determine the temporary IP Address of the VSP in a DHCP environment.
• Option B: Set the IP address of the VSP in a non-DHCP environment.
Option A: DHCP Network Environment
To determine a temporary IP address for the VSP:
1. In the VMware vSphere Client window, select the Summary tab and wait 5-10 minutes for
the IP address to appear (in the General section, IP address field).
2. Make a note of this VSP IP address, and launch HP 3PAR SmartStart.
Connecting to a Virtual Service Processor 65
- Storage Installation Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 General Site Planning 6
- Acclimatization 8
- 2 Getting Started 9
- Inspecting the Packaging 10
- Storage System Installation 11
- Disk Drive Numbering 12
- Controller Nodes 13
- I/O Modules 17
- Power Cooling Modules 17
- Service Processor 19
- Power Distribution Units 19
- Important Safety Information 20
- Required Tools 21
- Additional requirements 21
- Configurations 21
- • 1U and 0U configurations 22
- Hardware Installation 23
- Hardware Installation 25 25
- Installing the 1U and 0U PDUs 27
- • 0U bracket installation 28
- 3. Install cage nuts 28
- Securing the Cables 29
- Installation is complete 30
- Unpacking the Cabinet 31
- Positioning the Cabinet 31
- Verify the Cabling 32
- Removing the Brackets 34
- Installing the Rail Kit 35
- Installing the Rail Kit 37 37
- Installing Enclosures 38
- (LFF) disk drive) 40
- Installing a Disk Drive 41
- NoneRound hole 43
- NoneSquare hole 43
- ScrewdriverThreaded hole 43
- • Screwdriver 44
- 7 Cabling the Storage System 50
- Cabling Expansion Cabinets 51
- Cabling the Service Processor 52
- Cabling the Power Strips 53
- Verifying Setup 54
- Verifying LED Status 56
- Figure 37 Disk Drive LEDs 57
- Table 9 PCM LED Descriptions 58
- Node Interconnect Ports 60
- Drive Enclosure LEDs 61
- Figure 42 Front Panel LEDs 62
- Table 11 Front panel LEDs 62
- Figure 43 Rear Panel LEDs 63
- Table 12 Rear panel LEDs 63
- Prerequisites for Using a VSP 64
- Deploying the VSP OVF File 65
- Launching HP 3PAR SmartStart 72
- Generate Service Processor ID 75
- Configure SP Networking 76
- Remote Support 77
- System Support Information 79
- Time and Region 80
- Change Passwords 81
- Applying Settings 83
- Figure 57 Apply Settings 84
- Verify Storage System 88
- Configure Networking 89
- ◦ Subnet Mask 89
- ◦ Gateway 89
- Configuring Time 89
- Figure 65 Configure Time Page 90
- Change Password 91
- Verify Configuration 92
- Progress 92
- Figure 68 Progress Page 93
- Figure 69 Results Page 93
- Contacting HP 95
- HP 3PAR documentation 95
- Typographic conventions 98
- HP 3PAR branding information 98
- 12 Documentation feedback 99
- Figure 74 7000 Series PCM 101
- Figure 75 M6700 Series PCM 102
- Figure 77 SFF Drive Assembly 102
- Figure 79 LFF Drive Assembly 103
- Accessory Kits 104
- Rail Kits 104
- Rail Kits 105 105
- Figure 87 M5 Cage Nut 106
- Adding Disk Drives 110
- Checking Progress 111
- Completing the Upgrade 112
- SmartStart is Unavailable 113
- E Validating Remote Support 114
- G Troubleshooting 117
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales