Apple Processor Cage and Clips Guía de instalación Pagina 64
- Pagina / 117
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9 Initializing the Service Processor
The SP supports all actions required for maintenance of the storage system. The service processor
provides real-time, automated monitoring and remote access to HP 3PAR Support in order to
diagnose and resolve potential problems. An HP 3PAR StoreServ system can include either a virtual
or physical SP.
Use the following table as guidance for setting up a specific type of service processor.
ActionType of Service Processor
See “Connecting to a Virtual Service Processor” (page 64).Virtual Service Processor (VSP)
See “Connecting to a Physical Service Processor” (page
67).
Physical Service Processor
Connecting to a Virtual Service Processor
Prerequisites for Using a VSP
Before you connect to a VSP, review and complete the following tasks:
• Ensure the ESXi time and date are properly set, either through the Network Time Protocol
(NTP) server or manually through the ESXi console. Setting the correct date and time ensures
VSP real-time monitoring and access.
• Verify both the VSP and StoreServ system are on the same subnet.
• Verify the VMware vSphere client is available before deploying the VSP OVF file. Access your
ESXi server to download the VMware vSphere client or visit https://my.vmware.com/web/
vmware/downloads.
NOTE: Open Virtualization Format (OVF) is an open standard for packaging and distributing
virtual machines or software.
• Verify the HP 3PAR Virtual Service Processor software DVD is available. If you cannot locate
the DVD, contact HP Support through http://www.hp.com/support and request assistance
with the HP 3PAR StoreServ 7000 Storage product.
WARNING! Do not install the VSP on the same StoreServ 7000 array because it may lead to
the inability of properly managing the array when connectivity to the storage is unavailable.
Provision the VSP on a VMware server and ensure the VSP boots from the local disk of the assigned
VMware server and not from the StoreServ 7000 LUNs.
CAUTION: VMware vMotion is not a supported application. Do not use vMotion to migrate the
VSP from one physical server to another. Using vMotion may cause communication failure and
interrupt system service.
64 Initializing the Service Processor
- Storage Installation Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 General Site Planning 6
- Acclimatization 8
- 2 Getting Started 9
- Inspecting the Packaging 10
- Storage System Installation 11
- Disk Drive Numbering 12
- Controller Nodes 13
- I/O Modules 17
- Power Cooling Modules 17
- Service Processor 19
- Power Distribution Units 19
- Important Safety Information 20
- Required Tools 21
- Additional requirements 21
- Configurations 21
- • 1U and 0U configurations 22
- Hardware Installation 23
- Hardware Installation 25 25
- Installing the 1U and 0U PDUs 27
- • 0U bracket installation 28
- 3. Install cage nuts 28
- Securing the Cables 29
- Installation is complete 30
- Unpacking the Cabinet 31
- Positioning the Cabinet 31
- Verify the Cabling 32
- Removing the Brackets 34
- Installing the Rail Kit 35
- Installing the Rail Kit 37 37
- Installing Enclosures 38
- (LFF) disk drive) 40
- Installing a Disk Drive 41
- NoneRound hole 43
- NoneSquare hole 43
- ScrewdriverThreaded hole 43
- • Screwdriver 44
- 7 Cabling the Storage System 50
- Cabling Expansion Cabinets 51
- Cabling the Service Processor 52
- Cabling the Power Strips 53
- Verifying Setup 54
- Verifying LED Status 56
- Figure 37 Disk Drive LEDs 57
- Table 9 PCM LED Descriptions 58
- Node Interconnect Ports 60
- Drive Enclosure LEDs 61
- Figure 42 Front Panel LEDs 62
- Table 11 Front panel LEDs 62
- Figure 43 Rear Panel LEDs 63
- Table 12 Rear panel LEDs 63
- Prerequisites for Using a VSP 64
- Deploying the VSP OVF File 65
- Launching HP 3PAR SmartStart 72
- Generate Service Processor ID 75
- Configure SP Networking 76
- Remote Support 77
- System Support Information 79
- Time and Region 80
- Change Passwords 81
- Applying Settings 83
- Figure 57 Apply Settings 84
- Verify Storage System 88
- Configure Networking 89
- ◦ Subnet Mask 89
- ◦ Gateway 89
- Configuring Time 89
- Figure 65 Configure Time Page 90
- Change Password 91
- Verify Configuration 92
- Progress 92
- Figure 68 Progress Page 93
- Figure 69 Results Page 93
- Contacting HP 95
- HP 3PAR documentation 95
- Typographic conventions 98
- HP 3PAR branding information 98
- 12 Documentation feedback 99
- Figure 74 7000 Series PCM 101
- Figure 75 M6700 Series PCM 102
- Figure 77 SFF Drive Assembly 102
- Figure 79 LFF Drive Assembly 103
- Accessory Kits 104
- Rail Kits 104
- Rail Kits 105 105
- Figure 87 M5 Cage Nut 106
- Adding Disk Drives 110
- Checking Progress 111
- Completing the Upgrade 112
- SmartStart is Unavailable 113
- E Validating Remote Support 114
- G Troubleshooting 117
© 2020, manymanuals.es. Todos los derechos reservados | 0.136 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales