Apple Xserve Intel (Late 2006) DIY Procedure for Logic B Manual de usuario

 Xserve (Late 2006)073-1082 Rev. ALogic BoardReplacement InstructionsFollow the instructions in this document carefully. Failure to follow these inst

Xserve (Late 2006) Logic Board Replacement Instructions 10Important: Each heat sink is connected to the logic board by a small 2-pin thermal sensor c

Xserve (Late 2006) Logic Board Replacement Instructions 11ProcessorsRelease the latch on the metal holder for the rst processor.Rotate the top of th

Xserve (Late 2006) Logic Board Replacement Instructions 12Video Mezzanine Card (if installed)Remove the four Phillips screws that fasten the mezzanin

Xserve (Late 2006) Logic Board Replacement Instructions 13Disconnect the optical drive cable from the logic board.Release the two locking levers on t

Xserve (Late 2006) Logic Board Replacement Instructions 14Release the nine thumbscrews that secure the logic board to the enclosure (highlighted in t

Xserve (Late 2006) Logic Board Replacement Instructions 15Installing the Replacement Logic BoardImportant: When replacing the logic board, make sure

Xserve (Late 2006) Logic Board Replacement Instructions 16Use a screwdriver to tighten the nine thumbscrews snuggly, but don’t overtighten.Slide the

Xserve (Late 2006) Logic Board Replacement Instructions 17Clean o any existing thermal grease on the top face of the rst processor using an alcohol

Xserve (Late 2006) Logic Board Replacement Instructions 18Use the edge of the package that the alcohol wipe came in as a spatula to spread the therma

Xserve (Late 2006) Logic Board Replacement Instructions 19Rotate the top of the holder to the closed position.Engage the latch on the processor holde

Xserve (Late 2006) Logic Board Replacement Instructions 2Removing the Xserve from a RackAlert users that the server will be unavailable for a period

Xserve (Late 2006) Logic Board Replacement Instructions 20Tighten the four captive Phillips mounting screws for the left processor heat sink in the o

Xserve (Late 2006) Logic Board Replacement Instructions 21Replacing the Fan ArrayAlign the power connector on the fan array with its connector on the

Xserve (Late 2006) Logic Board Replacement Instructions 22Tighten the ve Phillips screws that fasten the airow duct to the fan array, in the order

Xserve (Late 2006) Logic Board Replacement Instructions 23Replacing the PCI Riser Cards and Expansion CardsAlign the riser with slot 2 on the logic b

Xserve (Late 2006) Logic Board Replacement Instructions 24Changing the Ethernet ID LabelReplacing the logic board in the Xserve changes its Ethernet

Xserve (Late 2006) Logic Board Replacement Instructions 25Using the Updated Server Serial NumberWhen you use Server Assistant to install Mac OS X Ser

Xserve (Late 2006) Logic Board Replacement Instructions 3Opening the XserveLoosen the thumbscrews at the back of the top cover and slide the cover ba

Xserve (Late 2006) Logic Board Replacement Instructions 4Power SuppliesPull the handle to release the rst power supply and slide it out of the bay.

Xserve (Late 2006) Logic Board Replacement Instructions 5FB-DIMMsPush down the ejectors on the FB-DIMM slot.Holding the FB-DIMM by both top corners,

Xserve (Late 2006) Logic Board Replacement Instructions 6Airow DuctLoosen the ve Phillips screws that fasten the airow duct to the fan array.Pull

Xserve (Late 2006) Logic Board Replacement Instructions 7Fan ArrayLoosen the two thumbscrews that secure the fan array to the enclosure. Note: The th

Xserve (Late 2006) Logic Board Replacement Instructions 8Note: You may encounter some resistance around the fan array power connector during removal.

Xserve (Late 2006) Logic Board Replacement Instructions 9Disconnect the backplane-to-logic board cable from the drive interconnect backplane and remo