Apple Xserve (Early 2008) DIY Procedure for Front Panel Manual de usuario descargar pdf

 Xserve (Late 2006/Early 2008)

073-1102 Rev. B

Front Panel Board Cable

Replacement Instructions

Follow the instructions in this document carefully. Failure to follow these instructions could

damage your equipment and void its warranty.

Online instructions are available at http://www.apple.com/support/diy/.

Working Safely Inside the Xserve

Always touch the Xserve enclosure to discharge static electricity before you touch any

components inside the Xserve. To avoid generating static electricity, do not walk around the

room until you have nished working inside the server and have replaced the cover. To minimize

the possibility of damage due to static discharge, wear an antistatic wrist strap while you work

inside the Xserve.

Warning: Always shut down the Xserve and disconnect the power cords before opening

it to avoid damaging its internal components or the components you are installing. Don’t

open the server while it is turned on. Even after you shut down the Xserve, its internal

components can be very hot. Let it cool before you open it.

Tools Required

The only tool required for this procedure is a Phillips #1 screwdriver.

Removing the Xserve from a Rack

Alert users that the server will be unavailable for a period of time. 1.

Shut down the Xserve (see the Xserve User’s Guide for help) and then wait to let the Xserve 2.

internal components cool.

Warning: Always shut down the Xserve before opening it to avoid damaging its internal

components or the components you want to install or remove. Don’t open the Xserve

or try to install or remove items inside while it is turned on. Even after you shut down

the Xserve, its internal components can be very hot. Let it cool down for 5 to 10 minutes

before you open it.

1 2 3 4 5 6 7

Indice de contenidos

Pagina 1 - Front Panel Board Cable

 Xserve (Late 2006/Early 2008)073-1102 Rev. BFront Panel Board CableReplacement InstructionsFollow the instructions in this document carefully. Failu

Pagina 2 - Opening the Xserve

Xserve (Late 2006/Early 2008) Front Panel Board Cable Replacement Instructions 2Unplug all cables from the Xserve. 3. Note: If you have trouble relea

Pagina 3 - Airow Duct

Xserve (Late 2006/Early 2008) Front Panel Board Cable Replacement Instructions 3Removing the Installed Front Panel Board CableNote: Before you can re

Pagina 4 - Left PCI Riser Card

Xserve (Late 2006/Early 2008) Front Panel Board Cable Replacement Instructions 4Left PCI Riser CardLoosen the two captive screws that secure the left

Pagina 5 - Replacing the Airow Duct

Xserve (Late 2006/Early 2008) Front Panel Board Cable Replacement Instructions 5Installing the Replacement Front Panel Board CableConnect the replace

Pagina 6 - Closing the Xserve

Xserve (Late 2006/Early 2008) Front Panel Board Cable Replacement Instructions 6Ensure the airow duct ts ush all over, and does not protrude above

Pagina 7

Mas documentos para Software Apple Xserve (Early 2008) DIY Procedure for Front Panel

a Ver el documento Apple Xserve (Early 2008) DIY Procedure for Front Panel Manual de usuario

Apple Xserve (Early 2008) DIY Procedure for Front Panel Manual de usuario (7 paginas)

Comentarios a estos manuales

Sin comentarios

Apple Xserve (Early 2008) DIY Procedure for Front Panel Manual de usuario

Busca en linea o descarga Manual de usuario para Software Apple Xserve (Early 2008) DIY Procedure for Front Panel . Apple Xserve (Early 2008) DIY Procedure for Front Panel Board Cable User Manual Manual de usuario

Indice de contenidos

Mas documentos para Software Apple Xserve (Early 2008) DIY Procedure for Front Panel

Comentarios a estos manuales

Relacionado con productos y manuales para Software Apple Xserve (Early 2008) DIY Procedure for Front Panel